 |
|
TDIF Expansion Board for the Hammerfall®
Series,
HDSP 9652 and DIGI96® Series |
|
|
 |
The TEB (TDIF Expansion Board)
adds an 8-channel TDIF interface to all ADAT-capable RME cards (see
below). Special features include manual choice of clock reference,
status LEDs and a word clock output.
The TEB is designed for maximum flexibility. Used with the Hammerfall
series and the HDSP 9652, it can even be used at sample rates of 88.2 kHz and
96 kHz. Meeting the TDIF specification, Double Line mode uses two channels
in single speed to get one channel in double speed. Therefore at 88.2/96 kHz
4 channels are available.
Installation is done in a convenient manner using the supplied bracket. No PCI
slot on the motherboard is needed. The integrated Clock Select Switch sets the
TDIF reference clock, thus avoids any clocking problems even with 'problematic'
TDIF devices. |
|
|
|
Using the Expansion Boards is very
easy to do, thanks to the clearly structured and informative Settings
dialog of RME's cards. The TEB operates like any other converter with
ADAT input and output, but is connected internally. Therefore the input
selector has to be set to 'Internal'.
The TEB gets its clock either from the card or the external TDIF device.
This is selected via the switch at the slot bracket.
The Input Status displays the selected input (Internal), the current sample rate
(44.1/48) and format (Adat.)
The ADAT output of all cards operate in parallel to this TDIF output. When Hammerfall
or HDSP 9652 are operated in Double Speed mode, the TEB automatically converts
the audio data to Double Line mode. |
 |
|
|
|
| TDIF port: D-sub 25 pin |
| Supported sample rates: 44.1 kHz,
48 kHz, varispeed (33 - 57 kHz) |
| Double Line mode: 4 channels at
88.2 kHz and 96 kHz (not with DIGI96 series) |
| Word clock output: BNC, low-impedance
driver stage, 4 Vss into 75 Ohms, short-circuit-proof |
| Power supply uses 3.5" floppy
connector, 5 V DC, 100 mA |
| AEB needs no slot on the motherboard |
| Standard bracket, board dimensions AEB4:
75 x 95 mm |
| 2 internal cable 2-pin, 1 internal cable
3-pin, 1 power adapter cable 5 1/4" to 2 x 3.5" included |
|
|
|
 HDSP
9652
Two TEBs can be connected and operated simultaneously.
One TEB can be used together with either one AEBx-I or AEBx-O.
DIGI96
SERIES
TEBs use the internal ADAT interface of the
DIGI cards. Therefore they do not work with the DIGI96 (which did not support
ADAT).
One TEB can be connected and operated.
HAMMERFALL
DSP MULTIFACE / DIGIFACE
Multiface and Digiface use the Hammerfall DSP
PCI card. This card has no internal inputs or outputs. Therefore no Expansion
Boards can be used.
HAMMERFALL
SERIES
An operation with the Hammerfall or Hammerfall
Light requires board revision 1.5 or higher, because the internal connector
ADAT1Out was not implemented in earlier versions.
One TEB can be connected and operated. Additionally one AEBx-O can be used
simultaneously.
|
| MANUFACTURER'S SUGGESTED RETAIL PRICING |
|
|
|
See your local
distributor's website for current price information.
|
Copyright © 2002 RME. All rights reserved.
RME is a registered trademark.
This website contains names and marks of other companies.
|
